ccnp final exam qns 301 to 350

QUESTION 131 Which of the following are valid types of VTP advertisement (Choose all that apply)?
A. Domain advertisements
B. Advertisement requests from clients
C. Subset advertisements D. Summary advertisements Answer: B, C, D
QUESTION 132 You are a Cisco Certified Engineer. You are configuring a switching solution. What command do you use to allow IOS to handle IP datagrams with source routing header options (fill in the blank): Answer: ip source-route Explanation: According to Cisco: To allow the Cisco IOS software to handle IP datagrams with source routing header options, use the ip source-route global configuration command. To have the software discard any IP datagram containing a source-route option, use the no form of this command. ip source-route no ip source-route
QUESTION 133 You are a Cisco Certified Engineer. You are configuring a switching solution. What modification can you make to the spanning-tree protocol, so that the spanning-tree operations can enjoy reasonable performance as the network grows?
A. use Load balancing links
B. None of the choices.
C. use PortFast.
D. Configure access switched as root bridges
E. Properly place the root bridge Answer: E Explanation: According to Cisco: Spanning-Tree Protocol (STP) is a Layer 2 protocol designed to run on bridges and switches. The specification for STP is called 802.1d. The main purpose of STP is to ensure that you do not run into a loop situation when you have redundant paths in your network. Loops are deadly to a network. More information can be found at: this site
QUESTION 134 In VLAN, every time we have a modification, what has to be updated (Choose all that apply)?
A. configuration revision number
B. configuration revision flag field
C. configuration revision reset switch
D. configuration revision database Answer: A, D
QUESTION 135 You are a Cisco Certified Engineer. You are configuring a switching solution. What command should you use to determine the current spanning-tree state of a Token Ring port within your spanning tree configuration (fill in the blank): Answer: show spantree portstate Explanation: According to Cisco: Use the show spantree portstate command to determine the current spanning-tree state of a Token Ring port within a spanning tree. show spantree portstate [trcrf ]
QUESTION 136 You are a Cisco Certified Engineer. You are configuring a switching solution. You need to determine the spanning tree's root bridge. Which factor(s), apart from the MAC address, determine who will become the root bridge (Choose all that apply)?
A. IP address
B. The port cost
C. Path cost
D. Priority number
E. The port ID Answer: D Explanation: According to Cisco: When you configure a switch as the secondary root, the spanning-tree bridge priority is modified from the default value (32768) to 16384 so that the switch is likely to become the root for the specified VLANs if the primary root switch fails (assuming the other switches in the network use the default bridge priority of 32768). The MAC address is also needed in the determination.
QUESTION 137 You are a Cisco Certified Engineer. You are configuring a switching solution. What command do you use to display the MLS cache (fill in the blank): Answer: show mls entry Explanation: According to Cisco: Use the show mls command set to display MLS Layer 3 packet information in the MLSbased Catalyst 5000, 2926G, and 2926 series switches. show mls show mls rp {ip_addr} [noalias] show mls entry {[destination {ip_addr_spec}] [source {ip_addr_spec}] [flow {protocol} {src_port [port_num]} {dst_port}]} [rp {ip_addr}] show mls include show mls nde
QUESTION 138 You are a Cisco Certified Engineer. You are configuring a switching solution. You want to restore the default TCP window size which was altered yesterday. What command can you use (fill in the blank): Answer: no ip tcp window-size Explanation: According to Cisco: To alter the TCP window size, use the ip tcp window-size global configuration command. To restore the default value, use the no form of this command. ip tcp window-size bytes no ip tcp window-size bytes Window size in bytes. The maximum is 65535 bytes. The default value is 2144 bytes.
QUESTION 139 You are a Cisco Certified Engineer. You are configuring a switching solution. Which of the following are NOT done by the VLAN trunking protocol (Choose all that apply)?
A. to reduce parallel load sharing
B. to propagate global VLAN information.
C. to provide routing randomness
D. to set the trunk priority levels of adjacent switches.
E. to ensure that there is a trunk operating Answer: A, C, D, E Explanation: According to Cisco: Before you create virtual LANs (VLANs), you must decide whether to use VTP in your network. With VTP, you can make configuration changes centrally on one or more switches and those changes are automatically communicated to all the other switches in the network. VTP is a Layer 2 messaging protocol that maintains VLAN configuration consistency by managing the addition, deletion, and renaming of VLANs on a network-wide basis. VTP minimizes misconfigurations and configuration inconsistencies that can result in a number of problems, such as duplicate VLAN names, incorrect VLAN-type specifications, and security violations.
QUESTION 140 What is the VLAN default value for the default VLAN?
A. VLAN 1003
B. VLAN 1
C. VLAN ON
D. VLAN A
E. VLAN 0Answer: B
QUESTION 141 You are a Cisco Certified Engineer. You are configuring a switching solution. When you check that a switch and router are consistently configured for VLANs, Cisco recommends that VLAN ID 1 be used for ______ (Choose all that apply)?
A. security
B. load balancing
C. troubleshooting
D. management Answer: C, D Explanation: According to Cisco: VLANs are often associated with IP subnetworks. For example, all the end stations in a particular IP subnet belong to the same VLAN. Traffic between VLANs must be routed. Interface VLAN membership on the switch is assigned manually on an interface-by-interface basis. When you assign switch interfaces to VLANs using this method, it is known as interface-based, or static, VLAN membership. You can set these parameters when you create a VLAN in the management domain: VLAN number VLAN name VLAN type (Ethernet, FDDI, FDDI network entity title [NET], TrBRF, or TrCRF) VLAN state (active or suspended) Maximum transmission unit (MTU) for the VLAN Security Association Identifier (SAID) Bridge identification number for TrBRF VLANs Ring number for FDDI and TrCRF VLANs Parent VLAN number for TrCRF VLANs Spanning Tree Protocol (STP) type for TrCRF VLANs VLAN number to use when translating from one VLAN type to another More information can be found at: this site
QUESTION 142 To modify the VLAN parameters on an existing Ethernet VLAN, you need to perform (Choose all that apply)?
A. set vlanID vlan_num [name name] [said said] [mtu mtu] [translation vlan_num]
B. Go into privileged mode
C. set vlan vlan_num [name name] [state {active suspend}] [said said] [mtu mtu] [translation vlan_num]
D. Go into interface mode
E. set vlanint vlan_num [name name] [said said] [mtu mtu] [translation vlan_num] Answer: B, C Explanation: Not B: The question is about the catOS and as a result you do not have to go into privileged mode.
QUESTION 143 You are a Cisco Certified Engineer. You are configuring a switching solution. What command is valid for showing the spanning-tree statistical information (fill in the blank): Answer: show spantree statistics Explanation: According to Cisco: Use the show spantree statistics command to show spanning-tree statistical information. show spantree statistics mod_num/port_num [vlan] show spantree statistics {trcrf trbrf}mod_num Number of the module. port_num Number of the port. vlan (Optional) Number of the VLAN. trcrf Number of the Token Ring concentrator relay function VLAN. trbrf Number of the Token Ring bridge relay function VLAN.
QUESTION 144 You are a Cisco Certified Engineer. You are configuring a switching solution. What command could you use to check a module/port in order to display the trunking status (fill in the blank): Answer: show trunk Explanation: According to Cisco: Use the show trunk command to display trunking information for the switch. show trunk [mod_num[/port_num]] [detail]mod_num (Optional) Number of the module. /port_num (Optional) Number of the port. detail (Optional) Keyword to show detailed information about the specified trunk port.
QUESTION 145 Which of the following is true concerning VTP Pruning (Choose all that apply)?
A. it does not prune traffic fromVLANs that are pruning-ineligible
B. VLAN 1 is always pruning-eligible
C. it will prune traffic from VLANs that are pruning-ineligible D. VLAN 2 is always pruning-ineligible
E. VLAN 1 is always pruning-ineligible Answer: A, E
QUESTION 146 You are a Cisco Certified Engineer. You are configuring a switching solution. You have an Ethernet media trunk line that is to be configured to operate in ISL mode between two Cisco Switches, each having identical modules, software revisions, and VLAN configuration information. Which of the following are not required for the trunk to operate in ISL mode correctly (Choose all that apply)?
A. Identical trunk negotiation parameters at each end of the link
B. Identical duplex at each end of the link
C. Identical speed at each end of the link
D. Identical native VLAN parameters at each end of the link Answer: A, D Explanation: According to Cisco: The valid range of user-configurable ISL VLANs is 1-1001. The valid range of VLANs specified in the IEEE 802.1Q standard is 0-4095. In a network environment with non-Cisco devices connected to Cisco switches through 802.1Q trunks, you must map 802.1Q VLAN numbers greater than 1000 to ISL VLAN numbers. 802.1Q VLANs in the range 1-1000 are automatically mapped to the corresponding ISL VLAN. 802.1Q VLAN numbers greater than 1000 must be mapped to an ISL VLAN in order to be recognized and forwarded by Cisco switches.
QUESTION 147 You are a Cisco Certified Engineer. You are configuring a switching solution. You are troubleshooting problems on a Catalyst 5000 trunk. When there is disagreement about the VLAN configured to use the trunk, what should you do?
A. Reload the active VLAN configuration
B. None of the choices.
C. Explicitly set the trunk for the VLAN to be on.
D. Remove all the VLANs set
E. Clear the affected port and bring it up again. Answer: B Explanation: In this situation you may want to set or clear the VLANS on both ends. According to Cisco: A trunk is a pointto-point link between one or more Ethernet switch interfaces and another networking device such as a router or a switch. Trunks carry the traffic of multiple VLANs over a single link and allow you to extend VLANs across an entire network. Two trunking encapsulations are available on all Ethernet interfaces: Inter-Switch Link (ISL)-ISL is a Cisco-proprietary trunking encapsulation 802.1Q-802.1Q is an industry-standard trunking encapsulation
QUESTION 148 You are a Cisco Certified Engineer. You are configuring a VLAN trunk for fast Ethernet. Which trunking modes cannot request the port to convert the link into a trunk link (Choose all that apply)?
A. Negotiate
B. Designate
C. Nonegotiate D. Auto
E. Manual Answer: A, B, C, E Explanation: According to Cisco: Ethernet Trunking Modes Mode Function on Puts the port into permanent trunking mode and negotiates to convert the link into a trunk link. The port becomes a trunk port even if the neighboring port does not agree to the change. off Puts the port into permanent nontrunking mode and negotiates to convert the link into a nontrunk link. The port becomes a nontrunk port even if the neighboring port does not agree to the change. desirable Makes the port actively attempt to convert the link to a trunk link. The port becomes a trunk port if the neighboring port is set to on, desirable, or auto mode. auto Makes the port willing to convert the link to a trunk link. The port becomes a trunk port if the neighboring port is set to on or desirable mode. This is the default mode for all Ethernet ports. nonegotiate Puts the port into permanent trunking mode but prevents the port from generating DTP frames. You must configure the neighboring port manually as a trunk port to establish a trunk link.
QUESTION 149 What are the layers in a typical campus network (Choose all that apply)?
A. Access
B. Front
C. Distribution
D. Back
E. Core Answer: A, C, E
QUESTION 150 You are considering setting up multiplayer switching. Commands that will be used to configure an internal or external Multi-layer Switch Route Processor include: mls rp ip What is this command for?
A. for enabling MLSP
B. for placing an external route processor in the interface of the VTP domain switch
C. for assigning VLAN ID to route processor interface
D. for enabling the RSM interface
E. for entering into the router interface Answer: A

QUESTION 151 To configure VTP on a switch, you may need to use the following commands: set vtp domain What is this command for?
A. For determining management domain name
B. For enabling VTP pruning.
C. For selecting VTP version.
D. For verifying configuration set.
E. For verifying configuration. Answer: A QUESTION 152 You are a Cisco Certified Engineer. You are managing a switching solution that runs with Cisco devices. The high end of the tools for Web based device management is:
A. CWOS
B. CiscoView
C. CWIS
D. VLANDirector
E. Traffic Director
F. NetSYS Answer: B Explanation: According to Cisco: CiscoView 5.3, a member of the CiscoWorks2000 family, is a Web based device management application providing dynamic status, monitoring, and configuration information for the broad range of Cisco internetworking products. CiscoView displays a physical view of a device chassis, with colorcoding of modules and ports for at-a-glance status. Monitoring capabilities display performance and other statistics. Configuration capabilities allow comprehensive changes to devices, given requisite security privileges are granted.
QUESTION 153 You are a Cisco Certified Engineer. You are configuring a switching solution. You need to enter a switch into an existing VTP domain without altering the configurations of the systems currently on the domain. Which of the following is one of the conditions required to ensure that the new switch will not change the existing VTP domain configuration?
A. The switch must be in client mode.
B. The switch must be in a mode other than the client mode.
C. The VTP domain must not have a password assigned to it.
D. The trunk links must not be configured for ISL Answer: A Explanation: According to Cisco: You can configure a switch to operate in any one of these VTP modes: Server-In VTP server mode, you can create, modify, and delete VLANs and specify other configuration parameters (such as VTP version and VTP pruning) for the entire VTP domain. VTP servers advertise their VLAN configuration to other switches in the same VTP domain and synchronize their VLAN configuration with other switches based on advertisements received over trunk links. VTP server is the default mode. Client-VTP clients behave the same way as VTP servers, but you cannot create, change, or delete VLANs on a VTP client. Transparent-VTP transparent switches do not participate in VTP. A VTP transparent switch does not advertise its VLAN configuration and does not synchronize its VLAN configuration based on received advertisements. However, in VTP version 2, transparent switches do forward VTP advertisements that they receive out their trunk ports.
QUESTION 154 Where would you set up an ARP server for the virtual LAN (Choose all that apply)?
A. on an AMT host.
B. on a Cisco 5500/AIP
C. on a Cisco 7000/AIP D. on an AIP host Answer: A, C
QUESTION 155 You are a Cisco Certified Engineer. You are configuring a switching solution. Which of the following are NOT the valid ways to configure load sharing using trunk ports (Choose all that apply)?
A. using STP vector metrics
B. using ISL VLAN
C. using STP path costs
D. using STP port priorities
E. using STP SID Answer: A, B, E Explanation: According to Cisco: Load sharing divides the bandwidth supplied by parallel trunks connecting switches. To avoid loops, Spanning-Tree Protocol (STP) normally blocks all but one parallel link between switches. With load sharing, you divide the traffic between the links according to which VLAN the traffic belongs to. There are two ways to configure load sharing by using trunk ports: using STP port priorities or using STP path costs. If you configure load sharing using STP port priorities, both load-sharing links must be connected to the same switch. If you configure load sharing using STP path costs, each load-sharing link can be connected to the same switch or to two different switches.
QUESTION 156 To configure VTP on a switch, you may need to use the following commands: set vtp pruneeligible What is this command for?
A. For determining management domain name
B. For verifying configuration.
C. For enabling VTP pruning.
D. For selecting VTP version.
E. For verifying configuration set Answer: C
QUESTION 157 You are a Cisco Certified Engineer. You are configuring a switching solution. When you use the catalyst 5000 series switch SPAN feature, what are you trying to achieve?
A. identify the destination portion of a MAC source address.
B. identify the destination of ISL packets on the outbound switch.
C. identify the port that mirrors traffic to a protocol analyzer.
D. identify the destination of ISL packets on all other switches.
E. selects network traffic for analysis
F. identify the destination for the spanning-tree BPDU. Answer: E Explanation: According to Cisco: SPAN selects network traffic for analysis by a Catalyst 5000 family Network Analysis Module, a SwitchProbe device, or other RMON probe. SPAN mirrors traffic from one or more source ports
(Ethernet, Fast Ethernet, Token Ring, or FDDI) on any VLAN to a destination port for analysis ( More information can be found at: this site
QUESTION 158 You are considering to set up multiplayer switching. Commands that will be used to configure an internal or external Multi-layer Switch Route Processor include: interface What is this command for?
A. for enabling the RSM interface
B. for entering into the router interface
C. for placing an external route processor in the interface of the VTP domain switch
D. for assigning VLAN ID to route processor interface
E. for enabling MLSP Answer: B
QUESTION 159 Which of the following is true concerning VLAN membership (Choose all that apply)?
A. VLAN membership of a user always remains the same even when he/she is moved to another location.
B. VLAN membership of a user always changes when he/she is moved to another location.
C. membership can be static or dynamic
D. membership can be static only Answer: A, C
QUESTION 160 In VLAN, what is a configuration revision number?
A. A number for identifying changes to the network switch.
B. A number for identifying changes to the network router.
C. A number for identifying changes to the network topology Answer: C
QUESTION 161 You are a Cisco Certified Engineer. You are configuring a switching solution. You need to configure your set based distribution layer switching engine to AVOID participating in multilayer switching. What command must you use (fill in the blank): Answer: set mls disable Explanation: According to Cisco: Use the set mls command set to configure the MLS feature in the Catalyst 5000, 2926G, and 2926 series switches. set mls agingtime [agingtime] set mls disable set mls enable set mls include {route_processor_ip route_processor_name} set mls statistics protocol port_num
QUESTION 162 To create a new Token Ring TrBRF VLAN, you need to perform (Choose all that apply)?
A. set vlan vlan_num [name name] [state {active suspend}] [said said] [mtu mtu] [translation vlan_num]
B. Go into interface mode
C. set vlan vlan_num [name name] type trbrf [said said] [mtu mtu] bridge bridge_number [stp {ieee ibm}]
D. Go into privileged mode
E. set vlanID vlan_num [name name] [said said] [mtu mtu] [translation vlan_num] Answer: C, D
QUESTION 163 You are a Cisco Certified Engineer. You are configuring a switching solution. You need to find ways to conveniently manage your Catalyst Token Ring switches. What should you do (Choose all that apply)?
A. use RMON
B. use CiscoView for Token Ring
C. use CiscoView for LAN
D. use SNMP
E. use CiscoWorks for Token Ring
F. use CiscoWorks for IP Answer: A, D Explanation: According to Cisco: Most Token Ring switches, including the Catalyst Token Ring switches, can be managed using SNMP. There are a several SNMP MIB definitions for Token Ring information and switches. RMON is an industry-standard method for providing network statistics monitoring using SNMP. It also collects fault, performance, and configuration statistics. RMON can also be used to supplant traffic analyzers by providing packet capture or tracing data through the switch or on a ring.
QUESTION 164 Which of the following is NOT a part of the correct sequence of building up a VLAN (Choose all that apply)?
A. Assign ports.
B. Create VLAN.
C. Create VLAN domain naming scheme
D. Configure ports for trunking.
E. Remove the trunk when the trunk is no longer needed.
F. Set the baud rate for ports
G. Verify configuration. Answer: A, B, D, E, G
QUESTION 165 You are a Cisco Certified Engineer. You are configuring a switching solution with a set based switch. You need to disable SPAN. What command should you use (fill in the blank): Answer: set span disable Explanation: According to Cisco: SPAN selects network traffic for analysis by a Catalyst 5000 family Network Analysis Module, a SwitchProbe device, or other RMON probe. SPAN mirrors traffic from one or more source ports (Ethernet, Fast Ethernet, Token Ring, or FDDI) on any VLAN to a destination port for analysis. To disable SPAN, perform this task in privileged mode:Task Command Disable SPAN on the switch. set span disable [dest_mod/dest_port all] QUESTION 166 You are a Cisco Certified Engineer. You are configuring a switching solution. On a switch that participates in multilayer switching, what command can you use to assign a VLAN ID (fill in the blank): Answer: mls rp vlan-id Explanation: mls rp vlan-id To assign a VLAN ID, use the mls ip vlan-id interface configuration command. mls rp vlan-id vlan-id-num
QUESTION 167 Which of the following is true concerning the deployment of VLAN (Choose all that apply)?
A. all VLAN devices are members of the same subnet domain
B. all VLAN devices are members of the same IP domain
C. all VLAN devices are members of the same broadcast domain
D. we use VLANs to establish broadcast domains to enjoy efficient bandwidth utilization Answer: C, D
QUESTION 168 You are a Cisco Certified Engineer. You are configuring a switching solution. What is the switch set-base command that is comparable to the command 'show span' (fill in the blank): Answer: show spantree Explanation: According to Cisco: Use the show spantree command to display spanning-tree information for a VLAN. show spantree [vlan mod_num/port_num] [active]vlan (Optional) Number of the VLAN. If the VLAN number is not specified, the default is VLAN 1. mod_num (Optional) Number of the module. port_num (Optional) Number of the port on the module. active (Optional) Keyword that specifies to display only the active ports.
QUESTION 169 You are a Cisco Certified Engineer. You are configuring a switching solution. You configure load sharing by using STP path costs. Which of the following are NOT true (Choose all that apply)?
A. all priorities must be set to 100
B. load-sharing links can connect to different switches
C. all priorities must be set to 0
D. the switch must be restarted for the second time
E. both load-sharing links must connect to the same switch Answer: A, C, D, E Explanation: According to Cisco: Load sharing divides the bandwidth supplied by parallel trunks connecting switches. To avoid loops, Spanning-Tree Protocol (STP) normally blocks all but one parallel link between switches. With load sharing, you divide the traffic between the links according to which VLAN the traffic belongs to. There are two ways to configure load sharing by using trunk ports: using STP port priorities or using STP path costs. If you configure load sharing using STP port priorities, both load-sharing links must be connected to the same switch. If you configure load sharing using STP path costs, each load-sharing link can be connected to the same switch or to two different switches.
QUESTION 170 You are a Cisco Certified Engineer. You are configuring a switching solution. What command must you use to enable CGMP on a router interface (fill in the blank): Answer: ip cgmp Explanation: According to Cisco: CGMP was first implemented by Cisco to restrain multicast traffic in a layer 2 network. Because a switch is, by essence, not capable of looking at layer 3 packets, it cannot distinguish an IGMP packet. With CGMP, the router provides the interface between the hosts. The routers "talk" IGMP, and the switches "talk" CGMP. More information can be found at: this site

QUESTION 171 To create a new Ethernet VLAN, you need to perform (Choose all that apply)?
A. set vlan vlan_num [name name] [said said] [mtu mtu] [translation vlan_num]
B. set vlanID vlan_num [name name] [said said] [mtu mtu] [translation vlan_num]
C. Go into interface mode
D. set vlanint vlan_num [name name] [said said] [mtu mtu] [translation vlan_num]
E. Go into privileged mode Answer: A, E Explanation: Not E: The question is referring to catos and you as dont need to go into privileged mode.
QUESTION 172 You are considering to set up multiplayer switching. Commands that will be used to configure an internal or external Multi-layer Switch Route Processor include: mls rp vlan-id What is this command for?
A. for enabling MLSP
B. for assigning VLAN ID to route processor interface
C. for enabling the RSM interface
D. for placing an external route processor in the interface of the VTP domain switch
E. for entering into the router interface Answer: B
QUESTION 173 You are a Cisco Certified Engineer. You are configuring a switching solution. You want to take advantage of the Fast EtherChannel ports. Which of the following guidelines can help you avoid configuration problems that may cause a port to be automatically disabled (Choose all that apply)?
A. Allow some ports in a channel to be partly disabled.
B. Configure ALL the ports in a channel as dynamic.
C. Assign all ports in a channel to the same VLAN
D. Allow some ports in a channel to be disabled.
E. Allow all ports in a channel to be disabled.
F. Configure all ports in a channel to operate at the same speed but in different duplex modes. Answer: C Explanation:
According to Cisco: Cisco's Fast EtherChannel technology builds upon standards based 802.3 full duplex Fast Ethernet to provide network managers a reliable high speed solution for the campus network backbone. Fast EtherChannel provides bandwidth scalability within the campus by providing increments from 200 Mbps to 800 Mbps with multi-gigabit capacity in the future. Fast EtherChannel technology not only solves the immediate problem of scaling bandwidth within the network backbone today, but also paves the path for an evolution to standards-based Gigabit Ethernet and beyond, because Fast EtherChannel technology can be applied to support Gigabit EtherChannel. More information can be found at: this site
QUESTION 174 When configuring VTP, you want to set the management domain name. What command will you use?
A. set vtp domain
B. show vtp
C. set vtp
D. set vtp pruneeligible Answer: A
QUESTION 175 Which of the following are reasons to deploy Dynamic Trunking Protocol (Choose all that apply)?
A. for supporting auto-negotiation of IEEE 802.1QUESTION NO: trunks
B. for supporting auto-negotiation of ISL
C. for managing trunk negotiation in 2500 router supervisor engine software R 4.2 or later
D. for managing trunk negotiation in Catalyst supervisor engine software R 4.2 or later. Answer: A, B, D
QUESTION 176 When configuring VTP, you want to allow pruning to take effect. What command will you use?
A. show vtp
B. set vtp
C. set vtp domain
D. set vtp pruneeligible Answer: D
QUESTION 177 You are a Cisco Certified Engineer. You are configuring a switching solution. You have configured a catalyst switch to operate in a VTP mode. Your switch can no longer advertise its VLAN configuration. Which VTP modes are NOT currently effective (Choose all that apply)?
A. Client
B. Server
C. Host
D. Transparent
E. Native Answer: A, B, C, E Explanation: According to Cisco: You can configure a switch to operate in any one of these VTP modes: Server-In VTP server mode, you can create, modify, and delete VLANs and specify other configuration parameters (such as VTP version and VTP pruning) for the entire VTP domain. VTP servers advertise their VLAN configuration to other switches in the same VTP domain and synchronize their VLAN configuration with other switches based on advertisements received over trunk links. VTP server is the default mode. Client-VTP clients behave the same way as VTP servers, but you cannot create, change, or delete VLANs on a VTP client. Transparent-VTP transparent switches do not participate in VTP. A VTP transparent switch does not advertise its VLAN configuration and does not synchronize its VLAN configuration based on received advertisements. However, in VTP version 2, transparent switches do forward VTP advertisements that they receive out their trunk ports.
QUESTION 178 You are a Cisco Certified Engineer. You are configuring a switching solution. What command do you use to display only the blocked ports in your spanning tree environment (fill in the blank): Answer: show spantree blockedports Explanation: According to Cisco: Use the show spantree blockedports command to display only the blocked ports. show spantree blockedports [vlan_num]vlan_num (Optional) Number of the VLAN.
QUESTION 179 You are a Cisco Certified Engineer. You are configuring a switching solution. An Ethernet media trunk link is to be configured between two Cisco switches. These switches have identical modules, software revisions and VLAN configuration information. Which of the following are NOT required for the trunk to operate (Choose all that apply)?
A. The link must be point to point for ISL.
B. The link must be 100Mbs or slower
C. The link must use IEEE 802.1QUESTION NO: trunk protocol.
D. The link may use IEEE802.1QUESTION NO: trunk protocol when the SAID parameter is correctly set. Answer: A, B Explanation: According to Cisco: VLAN Trunk Protocol (VTP) reduces administration in switched network. When you configure a new VLAN on one VTP server, the VLAN is distributed through all switches in the domain. This reduces the need of configuring the same VLAN everywhere. VTP is a Cisco-proprietary protocol that is available on most of the Cisco Catalyst Family products. More configuration information can be found at: this site
QUESTION 180 What is the VLAN default value for TrCRF bridge mode?
A. IBM
B. SRB
C. OTP
D. ATM Answer: B